收藏本站
180mA, 1x/2x, White LED Charge Pump
in 3mm x 3mm TDFN
Table 1. Recommended Components
COMPONENT
DESIGNATION
C IN , C OUT
C1
D1, D2, D3
R SET
VALUE
1μF
0.22μF
0.47μF
—
As Required
MANUFACTURER
Taiyo Yuden
TDK
Taiyo Yuden
TDK
Taiyo Yuden
TDK
Nichia
Citizen
Kamaya
Panasonic
PART NUMBER
JMK107BJ105KA
C1005X5R0J105M
JMK105BJ224KV
C1005X5R0J224K
JMK105BJ474KV
C1005X5R0J474K
NSCW215T
CL-470S
—
DESCRIPTION
1μF ±10%, 6.3V X5R ceramic capacitors (0603)
1μF ±20%, 6.3V X5R ceramic capacitors (0402)
0.22μF ±10%, 6.3V X5R ceramic capacitor (0402)
0.22μF ±10%, 6.3V X5R ceramic capacitor (0402)
0.47μF ±10%, 6.3V X5R ceramic capacitor (0402)
0.47μF ±10%, 6.3V X5R ceramic capacitor (0402)
White LEDs
White LED flash module
1% resistor
Applications Information
Driving Fewer than Three LEDs
When driving fewer than three LEDs, connect any unused
LED_ directly to IN (Figure 3). When connected in this
manner, the corresponding LED driver is disabled.
Driving Camera Strobes/Flashes
The MAX1574’s 180mA output capability makes it suit-
able for driving white LED camera strobes/flashes. For
example, the typical operating circuit drives a 3-LED
flash module with up to 60mA/LED. To ensure 180mA
total drive capability at low input voltages, increase C1
to 0.47μF.
To drive fewer or more LEDs with regulated total cur-
rent up to 180mA or to reduce the number of connect-
ing wires, short LED1, LED2, and LED3 together. When
connected this way, some LED modules have good
LED-to-LED forward-voltage matching, while others
may require individual ballast resistors. It is a good
idea to keep the ballast resistance as low as practical
for reasonable matching because high-ballast resis-
tance reduces the output drive capability due to the
higher V OUT requirement.
Input Ripple
For LED drivers, input ripple is more important than out-
put ripple. Input ripple depends on the source supply’s
impedance. Adding a lowpass filter to the input further
reduces input ripple. Alternatively, increasing C IN to
2.2μF cuts input ripple in half with only a small increase in
footprint. The 1x mode always has very low input ripple.
Component Selection
Use only ceramic capacitors with an X5R, X7R, or better
dielectric. See Table 1 for a list of recommended parts.
PC Board Layout and Routing
The MAX1574 is a high-frequency switched-capacitor
voltage regulator. For best circuit performance, use a
solid ground plane and place C IN , C OUT , and C1 as
close to the MAX1574 as possible. Refer to the
MAX1574 evaluation kit for an example.
_______________________________________________________________________________________
7
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAX1575ETE+ IC LED DRVR WHITE BCKLGT 16-TQFN
MAX1576ETG+T IC LED DRVR WHITE BCKLGT 24-TQFN
MAX1577ZETA+T IC LED DRIVR BCKLGT FLASH 8-TDFN
MAX1582ETC+T IC LED DRVR WHITE BCKLGT 12-TQFN
MAX1583ZETB+T IC LED DRIVR PHOTO FLASH 10-TDFN
MAX1599ETA+T IC LED DRIVR WHITE BCKLGT 8-TDFN
MAX1614EUA+ IC DVR MOSFET HI-SIDE NCH 8-UMAX
MAX16800ATE/V+ IC LED DRIVR HIGH BRIGHT 16-TQFN
相关代理商/技术参数
MAX1574ETB-T 功能描述:LED照明驱动器 White LED 1x/2x Charge Pump RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX1574EVKIT 功能描述:LED 照明开发工具 Evaluation Kit for the MAX1574 RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装:
MAX1575ETE 功能描述:LED照明驱动器 White LED 1x/1.5x Charge Pump RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX1575ETE/V+ 功能描述:LED照明驱动器 White LED 1x/1.5x Charge Pump for Main and Sub-Displays RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX1575ETE/V+T 功能描述:LED照明驱动器 White LED 1x/1.5x Charge Pump for Main and Sub-Displays RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX1575ETE+ 功能描述:LED照明驱动器 White LED 1x/1.5x Charge Pump RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX1575ETE+T 功能描述:LED照明驱动器 White LED 1x/1.5x Charge Pump RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX1575ETE-T 功能描述:LED照明驱动器 White LED 1x/1.5x Charge Pump RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N